Wexxar Case Formers

The WF20 fully automatic case former introduces a new level of refinement and performance and raises the standards for ease of use, case forming quality and customer value. The WF20 features a case squaring system and an enhanced Pin & Dome system that together ensure accurate forming throughout imperfections found in corrugated boxes that can be impact efficiency and quality. Built for sustained high speed applications, for glue or tape, this operator friendly machine will handle your most demanding packaging needs.

• Compact, in-line design; highest quality, widely available hardware
• Unmanned operation - remote demand control
• Case opening without vacuum; WEXXAR patented technology
• High capacity case feed magazine
• All case feeding and forming functions independently air operated
• Positive case squaring and flap alignment
• Cases formed and delivered upright
• Broad case size range, easy set-up guides, easy operation and care
• Machine Tune-Assist feature for easy maintenance and monitoring
• Tilt-out tape head allows quick, easy tape roll change

• Aluminum, stainless steel and plated steel; entirely corrosion resistant
• Operation Level Discharge at absolute minimum 23 in. (584 mm). With leveling pads, the range is 24 in. (610 mm) to 28.5 in. (724 mm)
• Case magazine at 29 in. (736 mm) at minimum discharge – comfortable loading height Controls
• NEMA 12 UL/CSA listed standard electrical control
• Meets N.F.P.A.-79 standard
• 24 volt DC power supply built in for safe, low voltage operating controls
• PLC operated sequence and timing control
• Touch Screen (8” color) HMI for machine control and monitoring
• Power Requirement. 230VAC, 3 Phase, 60Hz (other voltages available) 0.7 kVA
• Air Requirement. 0.3 cu. ft. (8.5 L) per cycle at 90 p.s.i.(6 bar)
• Speed. Up to 20 c.p.m. depending on case size and case quality
• Tape System. DEKKA Model WEX-22 tape applicator head
• Other makes optional
• Approx. Weight. 1,300 Lb. (590 Kg.)
• Case Styles. R.S.C., H.S.C. or C.S.S.C.
• For other styles consult your WEXXAR representative
• Change-Over Time. Approximately 3 minutes using tool-less, color-coded size changeover

Back to top

The WF30 fully automatic case former introduces a new level of refinement and performance and raises the standards for ease of use, case forming quality and customer value. The WF30 features a case squaring system and an enhanced Pin & Dome system that together ensure accurate forming throughout the process and easy handling of common imperfections found in corrugated boxes that can impact efficiency and quality. Built for sustained high speed applications, for glue or tape, this operator friendly machine will handle your most demanding packaging needs.

• Compact, in-line design; highest quality, widely available hardware
• Unmanned operation - remote demand control
• Case opening without vacuum; WEXXAR patented technology
• High capacity case feed magazine
• All case feeding and forming functions independently air operated
• Positive case squaring and flap alignment
• Cases formed and delivered upright
• Broad case size range, easy set-up guides, easy operation and care
• Machine Tune-Assist feature for easy maintenance and monitoring
• Tilt-out tape head allows quick, easy tape roll change

• Aluminum, stainless steel and plated steel; entirely corrosion resistant
• Operation Level. Discharge at absolute minimum 23 in. (584 mm). With leveling pads, the range is 24 in. (610 mm) to 28.5 in. (724 mm)
• Case magazine at 29 in. (736 mm) at minimum discharge – comfortable loading height
• Controls. NEMA 12 UL/CSA listed standard electrical control
• Meets N.F.P.A.-79 standard
• 24 volt DC power supply built in for safe, low voltage operating controls
• PLC operated sequence and timing control
• Touch Screen (8” color) HMI for machine control and monitoring
• Power Requirement. 230VAC, 3 Phase, 60Hz (other voltages available) 0.7 kVA
• Air Requirement. 0.3 cu. ft. (8.5 L) per cycle at 90 p.s.i.(6 bar)
• Speed. Up to 30 c.p.m. depending on case size and case quality
• Tape System. DEKKA Model WEX-22 tape applicator head
• Other makes optional
• Approx. Weight. 1,300 Lb. (590 Kg.)
• Case Styles. R.S.C., H.S.C. or C.S.S.C.
• For other styles consult your WEXXAR representative
• Change-Over Time. Approximately 10 minutes using tool-less, color-coded size changeover

Back to top