The WF10 Fully Automatic Case Former / Case Erector showcases a revolutionary omni-handed feature which allows case packers to form right-handed and left-handed cases on the same machine without the need for specifically handed equipment. The fully automatic WF10 omni-handed case former is ideal for customers with multiple product sizes, allowing them to pack products in batches of left-oriented or right-oriented cases with a quick changeover in between. The WF10 case erector's positive case squaring, delivers square cases in a fully upright position, ready for packing.

• Speed: Maximum 10 cases per minute (CPM)
• Size maximum: L: 20 x W: 15 x D: 15 Maximum
• Size minimum (Smaller/Custom sizes available by request): L: 9 x W: 7 x D: 5 Minimum
• Positive Case Squaring System: Lines up and squares the case during sealing, creating visually appealing case output.
• Toolless Size Changes: Not only a truly tool free operation, but we have cut the time for a full size change to under 5 minutes.

 Click to view a demo video

Back to top

The WF20 fully automatic case former introduces a new level of refinement and performance and raises the standards for ease of use, case forming quality and customer value. The WF20 features a case squaring system and an enhanced Pin & Dome system that together ensure accurate forming throughout imperfections found in corrugated boxes that can be impact efficiency and quality. Built for sustained high speed applications, for glue or tape, this operator friendly machine will handle your most demanding packaging needs.

• Compact, in-line design; highest quality, widely available hardware
• Unmanned operation - remote demand control
• Case opening without vacuum; WEXXAR patented technology
• High capacity case feed magazine
• All case feeding and forming functions independently air operated
• Positive case squaring and flap alignment
• Cases formed and delivered upright
• Broad case size range, easy set-up guides, easy operation and care
• Machine Tune-Assist feature for easy maintenance and monitoring
• Tilt-out tape head allows quick, easy tape roll change

• Aluminum, stainless steel and plated steel; entirely corrosion resistant
• Operation Level Discharge at absolute minimum 23 in. (584 mm). With leveling pads, the range is 24 in. (610 mm) to 28.5 in. (724 mm)
• Case magazine at 29 in. (736 mm) at minimum discharge – comfortable loading height Controls
• NEMA 12 UL/CSA listed standard electrical control
• Meets N.F.P.A.-79 standard
• 24 volt DC power supply built in for safe, low voltage operating controls
• PLC operated sequence and timing control
• Touch Screen (8” color) HMI for machine control and monitoring
• Power Requirement. 230VAC, 3 Phase, 60Hz (other voltages available) 0.7 kVA
• Air Requirement. 0.3 cu. ft. (8.5 L) per cycle at 90 p.s.i.(6 bar)
• Speed. Up to 20 c.p.m. depending on case size and case quality
• Tape System. DEKKA Model WEX-22 tape applicator head
• Other makes optional
• Approx. Weight. 1,300 Lb. (590 Kg.)
• Case Styles. R.S.C., H.S.C. or C.S.S.C.
• For other styles consult your WEXXAR representative
• Change-Over Time. Approximately 3 minutes using tool-less, color-coded size changeover

 Click to view a demo video

Back to top

The WF30 automatic case former has re-invented the toolless set-up, offering simpler, "user obvious" features that mean a quick and easy case size adjustments for packaging lines. Box one is ready to run without the use of tools or guide-books. A color-coded, tactile guide offers a more efficient, friendly system for operators.

• • Speed: Maximum 30 cases per minute (CPM)
  • Size maximum: L: 24 x W: 17 x D: 16.5 Maximum E = 25
  • Size minimum (Smaller/Custom sizes available by request): L: 6 x W: 5 x D: 3.5 Minimum E = 6
  • Positive Case Squaring System: Lines up and squares the case during sealing, creating visually appealing case output.
  • Single Push Transport System: Combines linear bearing guides with a mechanically adjustable case pusher for case squaring.
  • Dekka high performance tape head case closure system is standard
  • Precision folded and sealed cases around the clock
  • Positive case opening without vacuum easily accepts marginal quality corrugated board
  • Large case feed magazine
  • Corrosion-resistant, inline construction
  • U.L. listed electrical panel
  • Simple 10 minute size changeover
  • Interlocked safety guarding

• • Pin & Dome: As flat case blank is injected into the two facing plates, the pins goes into the flutes and the dome pinches the corrugated tightly. The two plates then open to 90 degrees to perfectly square the case. Since no compressed air is used in this process, it greatly decreases contamination and is more durable than vacuum cups which can clog and wear.
  • Safety & Ergonomic Features: Floor level tending reduces strain; every machine Wexxar builds is fully guarded from in-feed to out-feed, interlocked safety guarding throughout the machine; easily accessed control and assemblies; palm e-switches located on both sides.
  • Dynamic Flap Folding: Wexxar case formers have a dynamic flap folding system. As long plow rails aren't used, the overall length of the machine is significantly more compact. All four of the flaps are power folded in one position.
  • Compliant Drive Belt: Each of the two facing unidrive drive belts is mounted on a spring mechanism. This allows a constant pressure to be exerted on the case, despite normal variations in case width. Even heavy cases are handled carefully and with great control.
  • Servo Motion Control: Where a movement can be fast, the mechanism quickly gets to a specific position. It can then slow down to ensure a process takes place with the optimum pressure and speed, such as the opening the blank case.
  • Non-Contacting Sensors: Proximity sensors are able to have a much greater operating lifetime and don't cause jams than contacting sensors.
  • In-Line Operation: By keeping the intake and outflow of the machine in line with the rest of the line, aisles are kept free, safety is improved and space is saved.
  • Simplicity of Construction: By planning through each step in the construction of the machine and its materials, Wexxar is able to greatly reduce potential problems.
  • Small Footprint: Compact operations allows Wexxar's machine to fit into virtually any application and production line.
  • Integrated Controls: Connecting each machine in the full production line through common equipment and protocols reduces complexity and problems while increasing overall control.
  • Feed Magazine: Wexxar's extraordinarily large feed magazine option allows much longer operating periods without restocking and supervision
  • Washdown Configuration: EnviroGuard I and II Level One - lower parts of the machine protected against incidental splashing from caustic agents. Level Two - machine protected against direct washdown with non-corrosive cleaning agents and protected against incidental splashing from caustic detergents. Call for list of parts and protection methods.
  • Tagout/Lockout: When a machine is locked out, it cannot be operated until all the safety features are in place.
  • Paint-Free Construction: No paint: no contaminating flakes, no extra maintenance required.
  • UL-Listed Electrical Panels: Wexxar meets or exceeds all standards, requirements and specifications
  • NEMA Electrical Specifications: Wexxar meets or exceeds all standards, requirements and specifications
  • Regional Service Available: Through Wexxar's operating partnership with 10 other Pro Mach companies, there are factory trained service specialists available across North America.

 Click to view a demo video

Back to top